Explanation of loader Serial Number:. Model 1. Model 2. The five digit Production Sequence Number identifies the order which the loader is produced. Engine Serial Number. Figure 3. The engine serial number is in the location shown [Figure 3]. Figure 4. The Delivery Report must be filled out by the dealer and signed by the owner or operator when the Bobcat loader is delivered. An explanation of the form must be given to the owner. Make sure it is filled out completely [Figure.
See Specifications Section and your. Bobcat dealer for available tires. Level II is available. The Bobcat loader is base-equipped with a standard operator cab as shown. Extra insulated cab is available as an option Reduced noise level. Replacing Filter Element s. Inspection And Maintenance. Checking The Coolant Level. Cleaning The Cooling System.
Replacing the Coolant. Checking Engine Oil. Replacing Oil And Filter. Oil Chart. Checking And Maintaining. Checking And Adding. Removing Oil From The. Checking And Adding Fluid. Replacing Hydraulic Fluid. Installing Lift Arm Support Device. Removing Lift Arm Support Device. Continued On Next Page. Emergency Exit. Lowering The Operator Cab.
Raising The Operator Cab. Cleaning Procedure. Wheel Nuts. Figure Always park the loader on a level surface. Put jackstands under the front axles and rear corners of the frame before running the engine for service. Failure to use jackstands can allow the machine to fall or move and cause injury or death. Put floor jack under the rear of the loader [Figure Lift the rear of the loader and install jackstands [Figure.
Put the floor jack under the front of the loader [Figure Lift the front of the loader and put jackstands under the axle tubes [Figure ]. NOTE: Make sure the jackstands do not touch the tires. Make sure tires clear the floor and any obstacles. Never work on a machine with the lift arms up unless the lift arms are secured by an approved lift arm support device.
Failure to use an approved lift arm support device can allow the lift arms or attachment to fall and cause injury or death. Service lift arm support device if damaged or if parts are missing. Using a damaged lift arm support or with missing parts can cause lift arms to drop causing injury or death.
Put jackstands under the rear corners of the loader frame Inset [Figure ]. Remove the lift arm support device Item 1 [Figure ] from storage position.
The operator must be in the operator's seat, with the seat belt fastened and seat bar lowered, until the lift arm support device is installed. Start the engine, and raise the lift arms all the way up. Have a second person install the lift arm support device Item 1 [Figure ] over the rod of one of the lift cylinders.
The lift arm support device must be tight against the cylinder rod. The tabs of the lift arm support device must be under the cylinder as shown Inset [Figure ]. Lower the lift arms slowly until the lift arm support device is held between the lift arms and lift cylinder [Figure The operator must be in the operator's seat, with the seat belt fastened and seat bar lowered, until the lift arm support device is removed and the lift arms are lowered all the way.
Start the engine, raise the lift arms all the way up. Have a second person remove the lift arm support device. Lower the lift arms all the way and stop the engine. Return the lift arm support device to storage position and secure with clamping knobs. Remove the jackstands. Check with your dealer if the operator cab has been damaged. The seat belt must be worn for roll over protection. Level I - Protection from falling bricks, small concrete blocks, and hand tools encountered in operations such as highway maintenance, landscaping, and other construction site services.
Level II - Protection from falling trees, rocks; for machines involved in site clearing, overhead demolition or forestry. Always stop the engine before raising or lowering the cab. Stop the loader on a level surface. Lower the lift arms.
If the lift arms must be up while raising the operator cab, install the lift arm support device. Install jackstands under the rear of the loader frame [Figure ].
Loosen the nut both sides at the front corners of the operator cab [Figure ]. Remove the nuts and plates [Figure ] both sides. Never modify operator cab by welding, grinding, drilling holes or adding attachments unless instructed to do so by Bobcat.
Changes to the cab can cause loss of operator protection from rollover and falling objects, and result in injury or death. Lift on the grab handle and bottom of the operator cab slowly until the cab is all the way up and the latching mechanism engages [Figure ].
NOTE: Always use the grab handles to lower the cab. Pull down on the bottom of the operator cab until it stops at the latching mechanism [Figure ].
Release the latching mechanism Inset [Figure ] and pull the cab all the way down. Install the plates and nuts [Figure ] both sides. Tighten the nuts to ft. The front opening on the operator cab and rear window provide exits. Rear Window If Equipped. Safety Signs and Safety Check for damaged signs decals and safety tread.
Replace any Tread signs or safety treads that are damaged or worn. Check the condition of cab. Lift Arms, Cyl. Hydraulic Fluid, Hoses and Check fluid level and add as needed. Check for damage and Tubelines leaks. Repair or replace as needed. Final Drive Trans. Chaincase Check oil level. Foot Pedals, Hand Controls, Check for correct operation. Repair or adjust as needed.
Parking Brake Check operation. Spark Arrestor Muffler Clean the spark chamber. Battery Check cables, connections and electrolyte level. Add distilled water as needed Steering Shaft Grease two fittings.
Drive Belt Check for wear or damage. Adjust as needed. Fan Drive Gearbox Check gear lube level. Add as needed. Alternator Belt Check belt tension and adjust as needed. Engine Oil and Filter Replace oil and filter. Use CD or better grade oil and Melroe filter. Fuel Filter Replace the filter element. Hydraulic Reservoir Replace the reservoir breather cap.
Breather Cap Hydraulic Reservoir Replace the fluid. Chaincase Replace the fluid. Case Drain Filters Replace the filters. Failure to do so will result in excessive wear and early failures. The service schedule is a guide for correct maintenance of the Bobcat loader. Put jackstands under the front axles and rear corners of the frame before running the engine for service. Failure to use jackstands can allow the machine to fall or move and cause injury or death. W Put the floor jack under the rear of the loader [B].
Lift the rear of the loader and install jackstands [B]. Put the floor jack under the front the loader [C]. Lift the front of the loader and put jackstands under the axle tubes [C]. NOTE: Make sure the jackstands do not touch the tires. Revised June 01 Instructions are necessary before operating or servicing machine.
Untrained operators and failure to follow instructions can cause injury or death [A]. The rear of the trailer must be blocked or supported [A] when loading or unloading the loader to prevent the front end of the trailer from raising up. Use the following procedure to fasten the Bobcat loader to the transport vehicle to prevent the loader from moving during sudden stops or when going up or down slopes [B].
Lower the bucket or attachment to the floor. Stop the engine. Engage the parking brake. Install chains at the front and rear loader tie down positions Inset [B].
Fasten each end of the chain to the transport vehicle. Example: Moving the loader onto a transport vehicle. Turn the key switch to ON and press the traction lock override button. If the electrical system is not functioning part of the brake system must be disassembled to move the loader. Adequately designed ramps of sufficient strength are needed to support the weight of the machine when loading onto a transport vehicle.
Wood ramps can break and cause personal injury. W Revised Jan. Install the kit and lift as shown [A]. The single point lift, supplied by Bobcat Company is designed to lift and support the Bobcat loader without affecting roll over and falling object protection features of the operator cab. Assemble front cab fasteners as shown in this manual. Never allow riders in the cab or bystanders within 15 feet 5 meters while lifting the machine.
Remove the lift arm support device Item 1 [A] from storage position. The operator must be in the operator's seat, with the seat belt fastened and seat bar lowered, until the lift arm support device is installed. Start the engine, and raise the lift arms all the way up. Have a second person install the lift arm support device Item 1 [B] over the rod of one of the lift cylinders. When the concept of a skid-steer loader was fully developed, with a growing number of customers finding new and new ways of using this machine, the company decided to give the car new functions.
Having received a new name, a new logo, a new color scheme, the Melroe loader became a new machine — a machine that will conquer success all over the world.
Manufacturers wondered how best to position a new car? Facebook Analytics This is a tracking technology which utilizes the so-called, "Facebook pixel" from the social network Facebook and is used for website analysis, ad targeting, ad measurement and Facebook Custom audiences.
The Bobcat Service catalog has illustrations of complex technical repair procedures or procedures that cannot be demonstrated in the usual way. Bobcat Service - provides a reduction in repair time and diagnostics of Bobcat equipment and are a valuable way to gain new knowledge and skills for specialists in various areas of technical maintenance of Bobcat special equipment.
Then the company bought out the rights to a compact 3-wheel loader Keller from the Keller brothers, who subsequently successfully cooperated with Bobcat.G Series. Printed in U. Instructions are necessary before operating or servicing machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service. Untrained operators and failure to follow instructions can cause injury or death. Your safety is involved! Never service the Bobcat Skid- Steer Loader without instructions. Use the correct procedure to lift or lower operator cab. Have good ventilation when welding or grinding painted parts. Wear dust mask when grinding painted parts. Toxic dust and gas can be bobcat 773 service manual free download. Avoid exhaust fume leaks which can kill without warning. Exhaust system bobcat 773 service manual free download be tightly sealed. Disconnecting or loosening any hydraulic tubeline, hose, fitting, component or a part failure can cause lift arms to drop. Do not go under lift arms when anti pop up chrome free download unless supported bobcat 773 service manual free download an approved lift arm support device. Bobcat 773 service manual free download it if damaged. Never work on loader with lift arms up unless lift arms are held by an approved lift arm support device. Replace if damaged. Never modify equipment or add attachments not approved by Bobcat Company. Stop, cool and clean engine of flammable materials before checking fluids. Never service or adjust loader with the engine running unless instructed to do so in the manual. Bobcat truck & loader Service Manuals PDF, spare parts catalog, fault codes and wiring diagrams. Bobcat Skid Steer Service Repair impotenzberatung.com Mb. edocr is the only document marketplace to facilitate free lead generation, SEO visibility, and document selling. All in a fast, secure, and fun site. FREE BOBCAT SKID STEER LOADER SERVICE REPAIR WORKSHOP MANUAL INSTANT DOWNLOAD (S/N & ABOVE, EUROPE ONLY S/N. Download Bobcat T S/N Operation & Maintenance Manual · Download Bobcat BOBCAT SKID STEER LOADER Service Repair Manual. Title: Bobcat Skid Steer Loader Service Repair Manual DOWNLOAD - & Above, , Author: Lois Roberts, Length: 2 pages. Bobcat Service Repair Manual - Free ebook download as PDF File .pdf), Text File .txt) or read book online for free. Bobcat Service. Bobcat G Turbo Loader Service and Parts Manual. Pages impotenzberatung.com format. 40 MB impotenzberatung.com format for super fast downloads! Serial Number Range. Bobcat Skid Steers PDF manuals Free Download Bobcat Skid Steer Service Repair impotenzberatung.com, Mb, Download. Bobcat Skid Steer. I found a lot of Bobcat service manuals with this manual search I down loaded the manual but theres a lot of changes between the 2. The secondary front auxiliary quick couplers 1 [Figure 8] are available a Field Installed Accessory. Lower the lift arms. Exhaust system must be tightly sealed. Workshop and Repair manuals. Lift the front of the loader and put jackstands under the axle tubes [Figure ]. Fuel Filter. The service schedule is a guide for correct maintenance of the Bobcat loader. If a model is linked, click to access to instant download page to buy and access. Oil Chart. Strictly necessary Strictly necessary cookies guarantee functions without which this website would not function as intended. This manual covers model B Bobcat skid steer loaders.